I just purchased a brand new DELL XPS13-7390 laptop and installed Tumbleweed on it. Unfortunately the screen flickers like crazy. If windows runs on the same laptop the screen works very well. Also if I connect an external screen to it everything works fine. What is the reason of this flickering? Did anybody have the same problem?
↧
TUMBLEWEED Screen flickering on DELL XPS-13-7390
↧
LEAP 15.1 Hardware doesn't seem configured correctly: 2014 Macbook
Hello! I'm kinda baffled by this problem I'm facing. Hardware may or may not be the right section for this but I'm in the dark and it doesn't seem like a software problem...
So here we go:
Made the switch from OSX to Leap on my workhorse Macbook about a month ago, I'm fairly experienced with using Lynux distros but not opensuse (yet). I noticed that the battery life was immediately shortened with this new install (not a huge deal), then when the computer is locked and closed it still heats up like it's running at full power (kinda strange). My solution as of late has been to simply shut it off when it's not going to be in use for a while, which is probably a good habit, but I'm still wondering if there's some kind of background process that runs and if it's possible to get that to suspend along with the OS. Maybe whatever sensor tells the system the screen is closed isn't functioning correctly? Or, could the OS not be sending signals to the hardware to go to sleep?
Other than that everything is functioning as it should. The system monitor isn't reporting any kind of strange behavior, and all the other hardware transferred over to Leap easily.
Any suggestions, topics, and/or rabbit holes you have in mind would be greatly appreciated!
________
Some basic technical specs on what I'm running:
Early 2014 Macbook Pro 13
Intel Core i7-5557U CPU 3.1GHz
8 GiB RAM
Intel Iris Graphics 6100
Samsung Electronics SATA controller
Broadcom BCM43602 802.11ac Wireless LAN
Leap 15.1
KDE Plasma: 5.12.8
KDE Frameworks: 5.55.0
Qt Version: 5.9.7
Kernel: 4.12.14-lp151.28.36-default
64 bit
PS:
As I was doing to trouble-shooting before submitting this I checked the kernel messages and found this block of alerts reoccurring pretty often:
[ 9811.965966] CPU1: Core temperature above threshold, cpu clock throttled (total events = 6589)
[ 9811.965967] CPU3: Core temperature above threshold, cpu clock throttled (total events = 6589)
[ 9811.965969] CPU2: Package temperature above threshold, cpu clock throttled (total events = 14055)
[ 9811.965971] CPU0: Package temperature above threshold, cpu clock throttled (total events = 14055)
[ 9811.965972] CPU3: Package temperature above threshold, cpu clock throttled (total events = 14055)
[ 9811.965975] CPU1: Package temperature above threshold, cpu clock throttled (total events = 14055)
Does that look like it could be an issue? Could it be related to the one I mentioned at the top?
So here we go:
Made the switch from OSX to Leap on my workhorse Macbook about a month ago, I'm fairly experienced with using Lynux distros but not opensuse (yet). I noticed that the battery life was immediately shortened with this new install (not a huge deal), then when the computer is locked and closed it still heats up like it's running at full power (kinda strange). My solution as of late has been to simply shut it off when it's not going to be in use for a while, which is probably a good habit, but I'm still wondering if there's some kind of background process that runs and if it's possible to get that to suspend along with the OS. Maybe whatever sensor tells the system the screen is closed isn't functioning correctly? Or, could the OS not be sending signals to the hardware to go to sleep?
Other than that everything is functioning as it should. The system monitor isn't reporting any kind of strange behavior, and all the other hardware transferred over to Leap easily.
Any suggestions, topics, and/or rabbit holes you have in mind would be greatly appreciated!
________
Some basic technical specs on what I'm running:
Early 2014 Macbook Pro 13
Intel Core i7-5557U CPU 3.1GHz
8 GiB RAM
Intel Iris Graphics 6100
Samsung Electronics SATA controller
Broadcom BCM43602 802.11ac Wireless LAN
Leap 15.1
KDE Plasma: 5.12.8
KDE Frameworks: 5.55.0
Qt Version: 5.9.7
Kernel: 4.12.14-lp151.28.36-default
64 bit
PS:
As I was doing to trouble-shooting before submitting this I checked the kernel messages and found this block of alerts reoccurring pretty often:
[ 9811.965966] CPU1: Core temperature above threshold, cpu clock throttled (total events = 6589)
[ 9811.965967] CPU3: Core temperature above threshold, cpu clock throttled (total events = 6589)
[ 9811.965969] CPU2: Package temperature above threshold, cpu clock throttled (total events = 14055)
[ 9811.965971] CPU0: Package temperature above threshold, cpu clock throttled (total events = 14055)
[ 9811.965972] CPU3: Package temperature above threshold, cpu clock throttled (total events = 14055)
[ 9811.965975] CPU1: Package temperature above threshold, cpu clock throttled (total events = 14055)
Does that look like it could be an issue? Could it be related to the one I mentioned at the top?
↧
↧
TUMBLEWEED Pulse audio outputting s32le when set to s24le
Hello,
My speakers/sound-monitors are active and they feed 24bit/192 audio. When I configured my Pulseaudio conf file to s24le and either 192000 or 96000 it magically switches itself to s32le. I have avoid re-sampling on(but tested with off also) and after running "pactl list short sinks" it shows that it switches to s16/44100 when playing spotify, but then changes to S32/48000 when opening say youtube or vlc for example. It starts to sound like a compressor is running because it's sampling up and down. While things like youtube audio are not exactly premium listening experiences, I would like to avoid having it ever going into 32bit since the speaker amplifier can't handle that and downsample making everything sound overprocessed.
Thank you for the help.
My speakers/sound-monitors are active and they feed 24bit/192 audio. When I configured my Pulseaudio conf file to s24le and either 192000 or 96000 it magically switches itself to s32le. I have avoid re-sampling on(but tested with off also) and after running "pactl list short sinks" it shows that it switches to s16/44100 when playing spotify, but then changes to S32/48000 when opening say youtube or vlc for example. It starts to sound like a compressor is running because it's sampling up and down. While things like youtube audio are not exactly premium listening experiences, I would like to avoid having it ever going into 32bit since the speaker amplifier can't handle that and downsample making everything sound overprocessed.
Thank you for the help.
↧
OTHER VERSION [15.0] "network is unreachable" always same problem with WiFi, why?
Hi
I'm experiencing again a "network is unreachable" problem. I' love OpenSuse but I've always had these problems with WiFi networks since the old versions.
I don't know why it's so easy to break the network in Suse, but I would like to hope it's easy to fix it as well. Again, I totally say this as a constructive critic.
My current situation is the following: I bought a USB wireless card, I plugged it in my PC, I configured everything via Yast (wicked services) and everything worked.
Then I said to myself, why not using the NetworkManager app in the tray icon to choose the WiFi network in an easy way? well, I installed the network-manager gnome applet (dont' recall the correct name), I moved from Wicked to NetworkManager in Yast and then I tried to connect via the NetworkManager widget. I selected the correct network, wrote the password and after a while it prompt me again the request for the WiFi password, like if the password was wrong. I tried the suggestions I've found in this forum about checking the "save for all users" and some other checkbox, but nothing changed this behavior.. ti still asked me for the password again and again.
I said then: ok le'ts uninstall this widget (and I did) and let's go back to wicked. I tried again the wicked services, but I experienced the dreaded "network is unreachable" error on ping. I tried the ifup wlan0 and / or ifconfig wlan0 up commands, but no change. I then tried to plug the WiFI adapter in another USB port and in Yast I saw two adapters (why??): wlan0 and wlan1, I then deleted the wlan0 and still same problem with this new wlan1.
I tried both DHCP and manual configuration, using the google DNS and without using it. I tried also to change the options to enable the adatper at boot, manually or on hotplug, but now I'm stuck with this "network is unreachable" error.
Any suggestion? I would love also a suggestion for a book / good tutorial about how networking works on OpenSuse and how to fix these kind of problems.
Thank you and have a great Sunday
I'm experiencing again a "network is unreachable" problem. I' love OpenSuse but I've always had these problems with WiFi networks since the old versions.
I don't know why it's so easy to break the network in Suse, but I would like to hope it's easy to fix it as well. Again, I totally say this as a constructive critic.
My current situation is the following: I bought a USB wireless card, I plugged it in my PC, I configured everything via Yast (wicked services) and everything worked.
Then I said to myself, why not using the NetworkManager app in the tray icon to choose the WiFi network in an easy way? well, I installed the network-manager gnome applet (dont' recall the correct name), I moved from Wicked to NetworkManager in Yast and then I tried to connect via the NetworkManager widget. I selected the correct network, wrote the password and after a while it prompt me again the request for the WiFi password, like if the password was wrong. I tried the suggestions I've found in this forum about checking the "save for all users" and some other checkbox, but nothing changed this behavior.. ti still asked me for the password again and again.
I said then: ok le'ts uninstall this widget (and I did) and let's go back to wicked. I tried again the wicked services, but I experienced the dreaded "network is unreachable" error on ping. I tried the ifup wlan0 and / or ifconfig wlan0 up commands, but no change. I then tried to plug the WiFI adapter in another USB port and in Yast I saw two adapters (why??): wlan0 and wlan1, I then deleted the wlan0 and still same problem with this new wlan1.
I tried both DHCP and manual configuration, using the google DNS and without using it. I tried also to change the options to enable the adatper at boot, manually or on hotplug, but now I'm stuck with this "network is unreachable" error.
Any suggestion? I would love also a suggestion for a book / good tutorial about how networking works on OpenSuse and how to fix these kind of problems.
Thank you and have a great Sunday
↧
LEAP 15.2 VNCserver vs VNCmanager persistant
Hello there,
As seen in this guide, there are 2 different persistent VNC server sessions:
I can't figure out what is the difference, in the guide, I find the explanation of vncserver not clear to me and there is no comment on the vncmanager.
My use-case is:
I have a local desktop that I switch on/off every day running Opensuse 15.2 Mate DE.
I have a remote (in another room) laptop running Opensuse 15.2 Mate DE always on. Applications are running on and sometime I go to this laptop and work with it.
Both are connected on the local LAN.
I want to have access to the laptop DE from the desktop in the current running DE to control, start, stop, manage the running applications and use the DE as if I am in front of the laptop. When I disconnect the running applications should carry on.
Could you let me know what I can do and can't with both of type?
Many thanks
As seen in this guide, there are 2 different persistent VNC server sessions:
I can't figure out what is the difference, in the guide, I find the explanation of vncserver not clear to me and there is no comment on the vncmanager.
My use-case is:
I have a local desktop that I switch on/off every day running Opensuse 15.2 Mate DE.
I have a remote (in another room) laptop running Opensuse 15.2 Mate DE always on. Applications are running on and sometime I go to this laptop and work with it.
Both are connected on the local LAN.
I want to have access to the laptop DE from the desktop in the current running DE to control, start, stop, manage the running applications and use the DE as if I am in front of the laptop. When I disconnect the running applications should carry on.
Could you let me know what I can do and can't with both of type?
Many thanks
↧
↧
LEAP 15.1 SSD Read Write Error during install
Hi,
my PC has a Crucial MX500 SSD (with 1 TB capacity) bought less than one year ago. On this drive I have an openSUSE Linux 15.0 partition (EXT4 / ) and a Windows partition. Everything worked fine until a couple of months ago.
Recently openSUSE started to give me Read/Write errors while performing massive writing operations like Linux ISO images download, or Steam/GoG games install/update. When this happens, the entire Desktop Environment (KDE in my case) almost freeze completely, but the mouse still works, and I can go to the TTY with CTRL + ALT + F1.
Sadly from the TTY I'm unable to login, because it ask me a username without letting me type, so I think the entire system is in a strange status of non kernel panic, but unable to give it commands.
After an hard reset, the operating system works fine unless you perform big write operations like downloading the openSUSE ISO image file.
SMART parameters are ok and even the Crucial SSD Utility for Windows says everything is fine (Windows itself works fine).
Since I thought it was an openSUSE failure, i tried to re-install it, taking the opportunity to jump to version 15.1, but happened the same thing almost at the end of the installing procedure:
Same problem happens with KUbuntu, so I think it should be an hardware problem, but Windows is still working correctly and the Crucial SSD Tool says everything is fine.
Does someone have an idea about that? Does it could be a filesystem (EXT4) problem?
Thanks in advance,
Best Regards,
hawake
my PC has a Crucial MX500 SSD (with 1 TB capacity) bought less than one year ago. On this drive I have an openSUSE Linux 15.0 partition (EXT4 / ) and a Windows partition. Everything worked fine until a couple of months ago.
Recently openSUSE started to give me Read/Write errors while performing massive writing operations like Linux ISO images download, or Steam/GoG games install/update. When this happens, the entire Desktop Environment (KDE in my case) almost freeze completely, but the mouse still works, and I can go to the TTY with CTRL + ALT + F1.
Sadly from the TTY I'm unable to login, because it ask me a username without letting me type, so I think the entire system is in a strange status of non kernel panic, but unable to give it commands.
After an hard reset, the operating system works fine unless you perform big write operations like downloading the openSUSE ISO image file.
SMART parameters are ok and even the Crucial SSD Utility for Windows says everything is fine (Windows itself works fine).
Since I thought it was an openSUSE failure, i tried to re-install it, taking the opportunity to jump to version 15.1, but happened the same thing almost at the end of the installing procedure:
Code:
Subprocess failed. Error: RPM non riuscito: error: rpmdb: fsync
error: db4 error(30) from db->sync: Read-only file system
error: rpmdb: write: 0x1ecab18, 4096: Read-only file system
error: rpmdb: Name: write failed for page 2
error: rpmdb: Name: unable to flush page: 2
[...]
error: db4 error (30) from dbenv->close: Read-only file systemDoes someone have an idea about that? Does it could be a filesystem (EXT4) problem?
Thanks in advance,
Best Regards,
hawake
↧
TUMBLEWEED Zypper dup speeds terrible
Terrible speeds doing updates, how do I reset mirrorlist to Canada and US only?
↧
TUMBLEWEED python3-openshot problem
Hi!
Recently, when trying to zypper-dup, I found this problem:
I have tried suggested solutions 1 and 2 but they keep showing successive problems. The repositories I'm using are:
I did zypper clean and zypper refresh, and I was wondering what else I could do to proceed with the dup, or whether I should rather wait.
Thanks in advance for any help or suggestion you can kindly provide.
Recently, when trying to zypper-dup, I found this problem:
Code:
Computing distribution upgrade...
2 Problems:
Problem: python3-openshot-0.2.3+333-1.4.x86_64 requires python(abi) = 3.7, but this requirement cannot be provided
Problem: libreoffice-pyuno-6.4.2.1-1.2.x86_64 requires python(abi) = 3.8, but this requirement cannot be provided
Problem: python3-openshot-0.2.3+333-1.4.x86_64 requires python(abi) = 3.7, but this requirement cannot be provided
deleted providers: python3-base-3.7.3-1.4.x86_64
Solution 1: deinstallation of python3-openshot-0.2.3+333-1.4.x86_64
Solution 2: keep obsolete python3-base-3.7.3-1.4.x86_64
Solution 3: break python3-openshot-0.2.3+333-1.4.x86_64 by ignoring some of its dependencies
Choose from above solutions by number or skip, retry or cancel [1/2/3/s/r/c/d/?] (c):Code:
1 | Packman_Essentials | Packman_Essentials | Yes | (r ) Yes | Yes | http://ftp.gwdg.de/pub/linux/misc/packman/suse/openSUSE_Tumbleweed/Essentials/
2 | Science | Science | Yes | (r ) Yes | Yes | http://download.opensuse.org/repositories/science/openSUSE_Tumbleweed/
3 | download.opensuse.org-non-oss | Main Repository (NON-OSS) | Yes | (r ) Yes | Yes | http://download.opensuse.org/tumbleweed/repo/non-oss/
4 | download.opensuse.org-oss | Main Repository (OSS) | Yes | (r ) Yes | Yes | http://download.opensuse.org/tumbleweed/repo/oss/
5 | download.opensuse.org-tumbleweed | Main Update Repository | Yes | (r ) Yes | Yes | http://download.opensuse.org/update/tumbleweed/
6 | http-download.opensuse.org-77fcd3fb | openSUSE:Tumbleweed | Yes | (r ) Yes | Yes | http://download.opensuse.org/repositories/openSUSE:/Tumbleweed/standard/
7 | openSUSE-20161226-0 | openSUSE-20161226-0 | No | ---- | ---- | hd:/?device=/dev/sda2
8 | openSUSE_Tumbleweed | Games | Yes | (r ) Yes | Yes | http://download.opensuse.org/repositories/games/openSUSE_Tumbleweed/
9 | retroshare | retroshare | Yes | (r ) Yes | Yes | https://download.opensuse.org/repositories/network:/retroshare/openSUSE_Tumbleweed/
10 | skype-stable | skype (stable) | Yes | (r ) Yes | Yes | https://repo.skype.com/rpm/stable/Thanks in advance for any help or suggestion you can kindly provide.
↧
LEAP 15.1 X.org freezes
Hi! I have had this problem before and I had to completely reinstall the system.
This time I haven't installed any software or changed any settings. After a reboot my X.org keeps freezing up and behaving weirdly. The mouse pointer moves when I move the mouse, when I click a shortcut to run Firefox for example, I don't see the program's window popping up until I "manually refresh the screen" by opening another terminal with Ctrl+Alt+F1 and switching back to the X server with Ctrl+Alt+F7.
I've tried booting up from the different snapshots and restarting the X server with Ctrl+Alt+Backspace and it didn't help.
This time I haven't installed any software or changed any settings. After a reboot my X.org keeps freezing up and behaving weirdly. The mouse pointer moves when I move the mouse, when I click a shortcut to run Firefox for example, I don't see the program's window popping up until I "manually refresh the screen" by opening another terminal with Ctrl+Alt+F1 and switching back to the X server with Ctrl+Alt+F7.
I've tried booting up from the different snapshots and restarting the X server with Ctrl+Alt+Backspace and it didn't help.
↧
↧
LEAP 15.1 Not able to connect to wifi-access point
In
https://forums.opensuse.org/showthre...-BCM4352/page4
(which I shouldn't have used, since the problem is not with Tumbleweed, as as this thread, but with Leap 15.1),
I was advised to install broadcom-wl and broadcom-wl-kmp-default packages to get the ASUS PCE-AC56 wordking with Leap 15.1.
A good advice, because now the card is seen, and the hardware sees the wifi-networks available in the environment.
But when I enter the credentials for the wifi-point I want to use (the wifi-point as such is detected correctly), it is some seconds apparently trying to connect to the access point, but then keeps asking for the WPA2 passwd. The passwd is correct, our mobile phones connect to the same access point with the same password, and I checked it in the router settings.
The network is managed by Networkmanager. The settings for this wifi-connection gives all users access to the network, and the WPA2-key is given there too.
hwinfo --netcard says
Modprobe bcma doesn't change anything, and is revoked on reboot.
ip address says
and in journalctl these messages show after trying to connect:
Any one with an idea how I can establish the connection? Preferable without having to enter the root passwd...
Many thanks in advance!
https://forums.opensuse.org/showthre...-BCM4352/page4
(which I shouldn't have used, since the problem is not with Tumbleweed, as as this thread, but with Leap 15.1),
I was advised to install broadcom-wl and broadcom-wl-kmp-default packages to get the ASUS PCE-AC56 wordking with Leap 15.1.
A good advice, because now the card is seen, and the hardware sees the wifi-networks available in the environment.
But when I enter the credentials for the wifi-point I want to use (the wifi-point as such is detected correctly), it is some seconds apparently trying to connect to the access point, but then keeps asking for the WPA2 passwd. The passwd is correct, our mobile phones connect to the same access point with the same password, and I checked it in the router settings.
The network is managed by Networkmanager. The settings for this wifi-connection gives all users access to the network, and the WPA2-key is given there too.
hwinfo --netcard says
Code:
18: PCI 300.0: 0282 WLAN controller
[Created at pci.386]
Unique ID: y9sn.fkUtWxV49cB
Parent ID: gZD2.Gxy18Qr5+gA
SysFS ID: /devices/pci0000:00/0000:00:0b.0/0000:03:00.0
SysFS BusID: 0000:03:00.0
Hardware Class: network
Model: "Broadcom BCM4352 802.11ac Wireless Network Adapter"
Vendor: pci 0x14e4 "Broadcom"
Device: pci 0x43b1 "BCM4352 802.11ac Wireless Network Adapter"
SubVendor: pci 0x1043 "ASUSTeK Computer Inc."
SubDevice: pci 0x85ba
Revision: 0x03
Driver: "wl"
Driver Modules: "wl"
Device File: wlan0
Features: WLAN
Memory Range: 0xdfff8000-0xdfffffff (rw,non-prefetchable)
Memory Range: 0xdfc00000-0xdfdfffff (rw,non-prefetchable)
IRQ: 19 (30359 events)
HW Address: a2:5f:9c:c2:7b:4d
Permanent HW Address: 04:d9:f5:7a:cb:d0
Link detected: yes
WLAN channels: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 36 38 40 42 44 46 48 52 54 56 58 60 62 64 100 102 104 106
WLAN frequencies: 2.412 2.417 2.422 2.427 2.432 2.437 2.442 2.447 2.452 2.457 2.462 2.467 2.472 2.484 5.18 5.19 5.2 5.21 5.22 5.23 5.24 5.26 5.27 5.28 5.29 5.3 5.31 5.32 5.5 5.51 5.52 5.53
WLAN encryption modes: WEP40 WEP104 TKIP CCMP
WLAN authentication modes: open sharedkey wpa-psk wpa-eap
Module Alias: "pci:v000014E4d000043B1sv00001043sd000085BAbc02sc80i00"
Driver Info #0:
Driver Status: bcma is not active
Driver Activation Cmd: "modprobe bcma"
Driver Info #1:
Driver Status: wl is active
Driver Activation Cmd: "modprobe wl"
Config Status: cfg=no, avail=yes, need=no, active=unknown
Attached to: #13 (PCI bridge)ip address says
Code:
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state DORMANT group default qlen 1000
link/ether aa:e8:50:f5:4f:ee brd ff:ff:ff:ff:ff:ffCode:
mrt 15 17:08:30 linux-vffq kernel: WARNING: CPU: 0 PID: 545 at ../net/wireless/sme.c:948 cfg80211_roamed+0x23e/0x270 [cfg80211]
mrt 15 17:08:30 linux-vffq kernel: Modules linked in: fuse xt_tcpudp ip6t_rpfilter ip6t_REJECT ipt_REJECT xt_conntrack ip_set nfnetlink ebtable_nat ebtable_broute br_netfilter bridge stp llc af_packet ip6table_nat nf_conntra>
mrt 15 17:08:30 linux-vffq kernel: soundcore btrfs xor zstd_decompress zstd_compress xxhash raid6_pq sr_mod cdrom hid_generic usbhid ata_generic nouveau video mxm_wmi wmi i2c_algo_bit drm_kms_helper syscopyarea sysfillrect >
mrt 15 17:08:30 linux-vffq kernel: CPU: 0 PID: 545 Comm: wl_event_handle Tainted: P W O 4.12.14-lp151.28.36-default #1 openSUSE Leap 15.1
mrt 15 17:08:30 linux-vffq kernel: Hardware name: System manufacturer System Product Name/M2N68-AM Plus, BIOS 1804 08/23/2010
mrt 15 17:08:30 linux-vffq kernel: task: ffff8801376ea200 task.stack: ffffc90000b3c000
mrt 15 17:08:30 linux-vffq kernel: RIP: 0010:cfg80211_roamed+0x23e/0x270 [cfg80211]
mrt 15 17:08:30 linux-vffq kernel: RSP: 0018:ffffc90000b3fde8 EFLAGS: 00010246
mrt 15 17:08:30 linux-vffq kernel: RAX: 0000000000000000 RBX: ffffc90000b3fe20 RCX: 0000000000000012
mrt 15 17:08:30 linux-vffq kernel: RDX: 0000000000000002 RSI: 00000000fffffe01 RDI: ffffffffa06d0bf7
mrt 15 17:08:30 linux-vffq kernel: RBP: ffffc90000b3fe10 R08: 0000000000000000 R09: 0000000000000000
mrt 15 17:08:30 linux-vffq kernel: R10: ffffc90000b3fd50 R11: 0000000000000064 R12: 00000000014000c0
mrt 15 17:08:30 linux-vffq kernel: R13: ffff880139d4d000 R14: ffff880137054300 R15: dead000000000100
mrt 15 17:08:30 linux-vffq kernel: FS: 0000000000000000(0000) GS:ffff88013fc00000(0000) knlGS:0000000000000000
mrt 15 17:08:30 linux-vffq kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
mrt 15 17:08:30 linux-vffq kernel: CR2: 00007fd706b374c4 CR3: 000000008546c000 CR4: 00000000000006f0
mrt 15 17:08:30 linux-vffq kernel: Call Trace:
mrt 15 17:08:30 linux-vffq kernel: wl_bss_roaming_done.isra.26+0xb5/0x100 [wl]
mrt 15 17:08:30 linux-vffq kernel: wl_notify_roaming_status+0x30/0x70 [wl]
mrt 15 17:08:30 linux-vffq kernel: ? down_interruptible+0x2d/0x50
mrt 15 17:08:30 linux-vffq kernel: wl_event_handler+0x73/0x1e0 [wl]
mrt 15 17:08:30 linux-vffq kernel: ? wl_notify_scan_status+0x300/0x300 [wl]
mrt 15 17:08:30 linux-vffq kernel: kthread+0x10d/0x130
mrt 15 17:08:30 linux-vffq kernel: ? kthread_create_worker_on_cpu+0x50/0x50
mrt 15 17:08:30 linux-vffq kernel: ret_from_fork+0x22/0x40
mrt 15 17:08:30 linux-vffq kernel: Code: 8d 4d 70 45 0f b6 85 90 00 00 00 45 8b 8d a8 00 00 00 4c 89 f7 48 8b 36 e8 10 a4 fd ff 48 85 c0 48 89 43 08 5a 0f 85 f9 fd ff ff <0f> 0b 48 8d 65 d8 5b 41 5c 41 5d 41 5e 41 5f 5d c3 4>
mrt 15 17:08:30 linux-vffq kernel: ---[ end trace 63e68e12822c9ad6 ]---Many thanks in advance!
↧
LEAP 15.1 YaST & zypper install and uninstall - application dependencies modifications/changes
Both install or change a lot of dependencies.
But when I uninstall an application that needed dependencies ‘modified’, why don’t they also remove or change back all those dependencies?
I am afraid of putting too much of what won’t be used IF I remove an application.
IE: Lollypop put in/changed about 45 or more dependencies, but when I uninstall it all of those added/changed dependencies are still hanging out in the system.
Another ‘BillL’ conundrum!
that is why I like to keep install logs separate in my home folder.
But when I uninstall an application that needed dependencies ‘modified’, why don’t they also remove or change back all those dependencies?
I am afraid of putting too much of what won’t be used IF I remove an application.
IE: Lollypop put in/changed about 45 or more dependencies, but when I uninstall it all of those added/changed dependencies are still hanging out in the system.
Another ‘BillL’ conundrum!
that is why I like to keep install logs separate in my home folder.
↧
TUMBLEWEED /boot/efi is not mounted
Dear all
On one of my computers the partition /boot/efi is not mounted automatically which results in a error when an update for grub is installed, the command
/usr/sbin/shim-install", "--config-file=/boot/grub2/grub.cfg
fails with error "No valid EFI partition"
here the my /etc/fstab:
which is not really different from my other computer which are mounting the /boot/efi partition automatically
On one of my computers the partition /boot/efi is not mounted automatically which results in a error when an update for grub is installed, the command
/usr/sbin/shim-install", "--config-file=/boot/grub2/grub.cfg
fails with error "No valid EFI partition"
here the my /etc/fstab:
Code:
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 / btrfs defaults 0 0
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 /.snapshots btrfs subvol=/@/.snapshots 0 0
UUID=2e104bf6-0865-49aa-9547-8d1ee41c6262 swap swap defaults 0 0
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 /var btrfs subvol=/@/var 0 0
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 /usr/local btrfs subvol=/@/usr/local 0 0
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 /tmp btrfs subvol=/@/tmp 0 0
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 /srv btrfs subvol=/@/srv 0 0
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 /root btrfs subvol=/@/root 0 0
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 /opt btrfs subvol=/@/opt 0 0
UUID=7b66d503-9d46-4338-9a4e-18b51f1fc94c /home xfs defaults 0 0
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 /boot/grub2/x86_64-efi btrfs subvol=/@/boot/grub2/x86_64-efi 0 0
UUID=062e2312-24b8-43dd-bdff-524be9fe0a14 /boot/grub2/i386-pc btrfs subvol=/@/boot/grub2/i386-pc 0 0
UUID=CC1A-13F7 /boot/efi vfat defaults 0 0↧
TUMBLEWEED AMDGPU-PRO
Hi! I am trying to install amdgpu-pro drivers.
My graphic card is gigabyte rx 5700xt.
OpenSUSE Tumbleweed. Kernel version 5.5.7-1-default.
installation fails on amdgpu-dkms building.
Logs:
https://pastebin.com/upZ5aUJ3
Moreover chrome lost hardware acceleration.
![]()
My graphic card is gigabyte rx 5700xt.
OpenSUSE Tumbleweed. Kernel version 5.5.7-1-default.
installation fails on amdgpu-dkms building.
Logs:
https://pastebin.com/upZ5aUJ3
Moreover chrome lost hardware acceleration.
↧
↧
LEAP 15.1 mouse buttons stopped working (Logitech MX 518)
Hi all,
my mouse (Logitech MX 518, not the original version but the new release - about one year old) stopped working in OpenSuse Leap 15.1. Another mouse works fine.
The cursor is fine, but the buttons do not seem to work or show "random" results. If I open a firefox browser, everything (even the buttons) works fine as long as I stay inside the firefox window. But if I switch to another window, it seems all button clicks are still captured by firefox. In Dolphin, every button click is handled as "on directory up". And on a blank desktop, the only action that works is "mouse wheel up/down", which seems to trigger switching between virtual desktops.
As my machine is dual boot and the mouse works fine in Win10, I assume it is not a hardware problem with the mouse. OpenSuse 15.1 has latest updates. The last time it worked was two days ago (13th march), the latest updates were on 9th.
Does anybody have suggestions how to do further analysis? I don't even know what keywords to use for a google search...
I found hints about a file "/etc/X.11/xorg.conf.d/11-mouse.conf", but this file does not exist.
Many thanks in advance
Wolfgang
my mouse (Logitech MX 518, not the original version but the new release - about one year old) stopped working in OpenSuse Leap 15.1. Another mouse works fine.
The cursor is fine, but the buttons do not seem to work or show "random" results. If I open a firefox browser, everything (even the buttons) works fine as long as I stay inside the firefox window. But if I switch to another window, it seems all button clicks are still captured by firefox. In Dolphin, every button click is handled as "on directory up". And on a blank desktop, the only action that works is "mouse wheel up/down", which seems to trigger switching between virtual desktops.
As my machine is dual boot and the mouse works fine in Win10, I assume it is not a hardware problem with the mouse. OpenSuse 15.1 has latest updates. The last time it worked was two days ago (13th march), the latest updates were on 9th.
Does anybody have suggestions how to do further analysis? I don't even know what keywords to use for a google search...
I found hints about a file "/etc/X.11/xorg.conf.d/11-mouse.conf", but this file does not exist.
Many thanks in advance
Wolfgang
↧
AMD Radeon & OpenSUSE 13.2
Such is the problem. There is a Radeon R9 270 video card, if I put a driver from the amd site, then everything works fine, but Steam does not see it. On the Internet, I found that if this happens, it is better to install from repo. Put. As a result, steam saw, but does not recognize video memory, writes that its 256 meters. Again I began to look for a solution in the internet, but I did not find a sensible answer. Maybe someone here is in the know. ?
↧
LEAP 15.1 virt-manager disk image size differences
I've been using Virtualbox for my test VMs forever basically and recently I decided that I would give virt-manager a try. So far I really like it a lot! But I found something curious.
First, here is a screenshot of the part that is odd.
https://i.imgur.com/r5jwZng.png
If I create the disk image by using the default option then the disk image allocates the full amount of space. If I instead select the option to create a custom image it is a dynamically growing image. And here is the verification.
The first one above was created by selecting the default option and the second was created using the custom option. Both are 16G images and both appear to be the same file format.
The problem here is that I would always like to have them created as the dynamically allocated image but I might sometimes forget that I would need to go through that extra step to do it
Is there a way to have it create the dynamically allocated images by default?
First, here is a screenshot of the part that is odd.
https://i.imgur.com/r5jwZng.png
If I create the disk image by using the default option then the disk image allocates the full amount of space. If I instead select the option to create a custom image it is a dynamically growing image. And here is the verification.
Code:
> du -sh *
17G opensuse15.1.qcow2
3.7M test.qcow2Code:
> file opensuse15.1.qcow2
opensuse15.1.qcow2: QEMU QCOW Image (v3), 17179869184 bytes
> file test.qcow2
test.qcow2: QEMU QCOW Image (v3), 17179869184 bytesIs there a way to have it create the dynamically allocated images by default?
↧
LEAP 15.1 How to activate DHCPP Server for Ethernet over USB conenction to Android Tablet in KDE Networkmger
Now with Corona keeping me far, far away from my multi monitor set up, I have to use my old laptop and a 12.2 Samsung Android Tablet as second monitor and an ipad mini as third.
the solution with https://github.com/kbumsik/VirtScreen does not work, as it needs an intel graphicscard,
So I connected back to my notebook from Android tablet via Wifi and started a XFCE VNC Session and started Quicksynergy client on the tablet and qsynergy server on the notebook.
But I hope the connection could be improved by using ethernet over USB.
On the Samsung Galaxy Tablet 12.2 SM-T900 runs Cyanogenmod /Lineage 14 and in the development options I can select
USB-configuration (USB-ethernet)
If I activate this configuration, K-Netowrkmanager tries to optain an IP address. So the connection could work. But I see no option in lineage to enter a static IP adress.
That means I need a DHCP server on OpenSUSE 15.1 networkmanager. Is there an option in networkmanager? every disconnect creates a new "WIRED NETWORK CONNECTION"
The Internet is shared through WiFi on another Android phone.
I hope to increase the VNC speed that way.
the solution with https://github.com/kbumsik/VirtScreen does not work, as it needs an intel graphicscard,
So I connected back to my notebook from Android tablet via Wifi and started a XFCE VNC Session and started Quicksynergy client on the tablet and qsynergy server on the notebook.
But I hope the connection could be improved by using ethernet over USB.
On the Samsung Galaxy Tablet 12.2 SM-T900 runs Cyanogenmod /Lineage 14 and in the development options I can select
USB-configuration (USB-ethernet)
If I activate this configuration, K-Netowrkmanager tries to optain an IP address. So the connection could work. But I see no option in lineage to enter a static IP adress.
That means I need a DHCP server on OpenSUSE 15.1 networkmanager. Is there an option in networkmanager? every disconnect creates a new "WIRED NETWORK CONNECTION"
The Internet is shared through WiFi on another Android phone.
I hope to increase the VNC speed that way.
↧
↧
LEAP 15.1 KDEwallet
KDE Wallet
Heb een probleempje bij het opstarten met de het activeren van mijn draadloze netwerkkaart.
Log normaal in op Suse Leap 15.1.
Krijg de melding voor het invoeren voor het wachtwoord voor Kwallet
Krijg de melding voor het invoeren voor het wachtwoord voor Kwallet
Zoals gebruikelijk voer ik het wachtwoord in, krijg dan de melding dat de draadloze interface (wlan1) de secrets niet zijn geleverd.
Daarna wordt de verbinding gedeactiveerd
Heeft iemand een tip om dit probleem op te lossen?
Heeft iemand een tip om dit probleem op te lossen?
↧
LEAP 15.1 Olivetti M220 port designation
I have apparently managed to install the driver for an elderly Olivetti M220 as CUPS reports that the printer is responding to it and it is sending jobs to it but none of the jobs are printed. I am not sure whether the printer is configured by default to use a non-standard port or whether this was the decision of the admin who set it up many years ago; however, the control panel lists two port numbers, one of which is described as an ASCII port number.
I have looked at the openSUSE documentation but I cannot see anything which says whether, in the YasT>Printer>Configuration wizard, the port should be entered in decimal or hex or what the significance of calling one port number ASCII is. Any assistance welcome.
I have looked at the openSUSE documentation but I cannot see anything which says whether, in the YasT>Printer>Configuration wizard, the port should be entered in decimal or hex or what the significance of calling one port number ASCII is. Any assistance welcome.
↧
TUMBLEWEED sysctl.conf still being ignored on boot
Hi
I have a setting to disable ipv6 in /etc/sysctl.conf and it is ignored at boot
I have to manually run
sudo sysctl -p
and the settings I've added (or are added by suse?) are then appied
I've had a look back though posts on these forums and cannot see an actual answer that works (including a thread from 2013)
/etc/sysctl.conf is defintely link to from /usr/lib/sysctl.d/99-sysctl.conf -> /etc/sysctl.conf
One thread suggested
But I got a response of
Running
tells me:
Running
Gives me what I want and reads /etc/sysctl.conf
But this does not happen at boot
Why?
In debian (which I use at work on multiple VMs, actual hardware etc of all OSes dating back years) this just works
But not in Tumbleweed
There is obviously some step I am missing that involves more than just putting an entry in /etc/sysctl.conf
(and has been for a while?)
But it should be possible to just add an entry in /etc/sysctl.conf and reboot and it to just work by default
If it doesn't, then is it a bug?
It really should not be a question of RTFM because manually running
works
Regards
I have a setting to disable ipv6 in /etc/sysctl.conf and it is ignored at boot
I have to manually run
sudo sysctl -p
and the settings I've added (or are added by suse?) are then appied
I've had a look back though posts on these forums and cannot see an actual answer that works (including a thread from 2013)
/etc/sysctl.conf is defintely link to from /usr/lib/sysctl.d/99-sysctl.conf -> /etc/sysctl.conf
Code:
ls -l /usr/lib/sysctl.d/99-sysctl.conf
lrwxrwxrwx 1 root root 16 Mar 6 21:05 /usr/lib/sysctl.d/99-sysctl.conf -> /etc/sysctl.confCode:
chkconfig -a boot.sysctlCode:
boot.sysctl: unknown serviceCode:
sudo systemctl enable systemd-sysctl.serviceCode:
The unit files have no installation config (WantedBy=, RequiredBy=, Also=,
Alias= settings in the [Install] section, and DefaultInstance= for template
units). This means they are not meant to be enabled using systemctl.
Possible reasons for having this kind of units are:
• A unit may be statically enabled by being symlinked from another unit's
.wants/ or .requires/ directory.
• A unit's purpose may be to act as a helper for some other unit which has
a requirement dependency on it.
• A unit may be started when needed via activation (socket, path, timer,
D-Bus, udev, scripted systemctl call, ...).
• In case of template units, the unit is meant to be enabled with some
instance name specified.Code:
sudo sysctl -pBut this does not happen at boot
Why?
In debian (which I use at work on multiple VMs, actual hardware etc of all OSes dating back years) this just works
But not in Tumbleweed
There is obviously some step I am missing that involves more than just putting an entry in /etc/sysctl.conf
(and has been for a while?)
But it should be possible to just add an entry in /etc/sysctl.conf and reboot and it to just work by default
If it doesn't, then is it a bug?
It really should not be a question of RTFM because manually running
Code:
sudo sysctl -pRegards
↧