Quantcast
Channel: openSUSE Forums
Viewing all 40713 articles
Browse latest View live
↧

TUMBLEWEED New journal errors after 2020-09-15 update.

September 16, 2020, 2:24 pm
$
0
0
Some of the errors have been around since the system was installed, and were present in Fedora as well. I filtered out the AER errors with grep, because they've been around for years. Here are the errors, the new ones are in bold:

Code:
> sudo journalctl -b -p err | grep -v 'AER:'
-- Logs begin at Mon 2020-08-24 10:14:44 PDT, end at Wed 2020-09-16 14:18:24 PDT. --
Sep 16 14:04:29 Mobile-PC kernel: pci 0000:00:00.2: AMD-Vi: Unable to read/write to IOMMU perf counter.
Sep 16 14:04:29 Mobile-PC systemd[1]: Failed to start Apply Kernel Variables.
Sep 16 14:04:29 Mobile-PC systemd-sysctl[217]: Couldn't write '"0 2147483647"' to 'net/ipv4/ping_group_range': Invalid argument
Sep 16 14:04:29 Mobile-PC kernel: i2c_hid i2c-DELL0812:00: HID over i2c has not been provided an Int IRQ
Sep 16 14:04:31 Mobile-PC systemd-sysctl[475]: Couldn't write '"0 2147483647"' to 'net/ipv4/ping_group_range': Invalid argument
Sep 16 14:04:31 Mobile-PC systemd[1]: Failed to start Apply Kernel Variables.
Sep 16 14:04:32 Mobile-PC systemd-sysctl[540]: Couldn't write '"0 2147483647"' to 'net/ipv4/ping_group_range': Invalid argument
Sep 16 14:04:32 Mobile-PC systemd[1]: Failed to start Apply Kernel Variables.
Sep 16 14:04:32 Mobile-PC systemd-sysctl[750]: Couldn't write '"0 2147483647"' to 'net/ipv4/ping_group_range': Invalid argument
Sep 16 14:04:32 Mobile-PC systemd[1]: Failed to start Apply Kernel Variables.
Sep 16 14:04:32 Mobile-PC systemd-sysctl[826]: Couldn't write '"0 2147483647"' to 'net/ipv4/ping_group_range': Invalid argument
Sep 16 14:04:32 Mobile-PC systemd[1]: Failed to start Apply Kernel Variables.
Sep 16 14:04:41 Mobile-PC lightdm[1537]: gkr-pam: unable to locate daemon control file
Sep 16 14:04:43 Mobile-PC bluetoothd[1142]: Failed to set mode: Blocked through rfkill (0x12)
Sep 16 14:06:19 Mobile-PC kernel: iommu ivhd0: AMD-Vi: Event logged [INVALID_DEVICE_REQUEST device=00:00.0 pasid=0x00000 address=0xfffffffdf8000000 flags=0x0a00]
Here is the list of packages that were updated immediately before the new errors started appearing:

Code:
> zypp-hist | grep '2020-09-15 13:1[6-9]'
2020-09-15 13:16:44 | command | root@Mobile-PC | 'zypper' 'dup'
2020-09-15 13:16:44 | install | PackageKit-gtk3-module | 1.2.1-1.1
2020-09-15 13:16:44 | install | boost-license1_74_0 | 1.74.0-2.1
2020-09-15 13:16:44 | install | chkstat | 1550_20200909-23.1
2020-09-15 13:16:44 | install | hostname | 3.23-1.1
2020-09-15 13:16:44 | install | iproute2 | 5.8.0-1.1
2020-09-15 13:16:45 | install | libQt5Core5 | 5.15.1-1.1
2020-09-15 13:16:45 | install | libacl1 | 2.2.53-4.1
2020-09-15 13:16:45 | install | libcares2 | 1.16.1-2.1
2020-09-15 13:16:45 | install | libefivar1 | 37-4.1
2020-09-15 13:16:45 | install | liblcms2-2 | 2.11-1.1
2020-09-15 13:16:45 | install | libmetis5 | 5.1.0-9.1
2020-09-15 13:16:46 | install | libmysofa1 | 1.1-2.1
2020-09-15 13:16:46 | install | libneon27 | 0.31.2-1.1
2020-09-15 13:16:46 | install | libopenblas_pthreads0 | 0.3.10-3.1
2020-09-15 13:16:46 | install | libp11-3 | 0.4.10-1.4
2020-09-15 13:16:47 | install | libseccomp2 | 2.5.0-1.1
2020-09-15 13:16:47 | install | libv4l | 1.20.0-2.1
2020-09-15 13:16:47 | install | openSUSE-release-appliance-custom | 20200914-692.1
2020-09-15 13:16:47 | install | opensc | 0.19.0-4.5
2020-09-15 13:16:48 | install | perl-HTTP-Message | 6.26-1.1
2020-09-15 13:16:48 | install | permissions-doc | 1550_20200909-23.1
2020-09-15 13:16:48 | install | xen-libs | 4.14.0_02-2.2
2020-09-15 13:16:48 | install | libboost_thread1_74_0 | 1.74.0-2.1
2020-09-15 13:16:48 | install | libboost_iostreams1_74_0 | 1.74.0-2.1
2020-09-15 13:16:48 | install | libboost_filesystem1_74_0 | 1.74.0-2.1
2020-09-15 13:16:48 | install | libboost_date_time1_74_0 | 1.74.0-2.1
2020-09-15 13:16:49 | install | permissions-config | 1550_20200909-23.1
2020-09-15 13:16:49 | install | libQt5Test5 | 5.15.1-1.1
2020-09-15 13:16:49 | install | libQt5Sql5 | 5.15.1-1.1
2020-09-15 13:16:49 | install | libQt5DBus5 | 5.15.1-1.1
2020-09-15 13:16:49 | install | vim-data-common | 8.2.1412-1.3
2020-09-15 13:16:49 | install | acl | 2.2.53-4.1
2020-09-15 13:16:50 | install | libv4lconvert0 | 1.20.0-2.1
2020-09-15 13:16:50 | install | openSUSE-release | 20200914-692.1
2020-09-15 13:16:51 | install | rng-tools | 6.10-1.1
2020-09-15 13:16:51 | install | libboost_locale1_74_0 | 1.74.0-2.1
2020-09-15 13:16:51 | install | permissions | 20200909.1550-23.1
2020-09-15 13:16:51 | install | libQt5Sql5-sqlite | 5.15.1-1.1
2020-09-15 13:16:51 | install | libQt5Positioning5 | 5.15.1-1.1
2020-09-15 13:16:52 | install | libQt5Network5 | 5.15.1-1.1
2020-09-15 13:16:52 | install | vim-data | 8.2.1412-1.3
2020-09-15 13:16:53 | install | libv4l2-0 | 1.20.0-2.1
2020-09-15 13:16:53 | install | aaa_base | 84.87+git20200909.ee4a72c-1.1
2020-09-15 13:16:53 | install | sudo | 1.9.2-3.1
2020-09-15 13:16:56 | install | chromium | 85.0.4183.102-1.1
2020-09-15 13:16:56 | install | libQt5XmlPatterns5 | 5.15.1-1.1
2020-09-15 13:16:56 | install | libQt5Gui5 | 5.15.1-1.1
2020-09-15 13:16:57 | install | vim | 8.2.1412-1.3
2020-09-15 13:16:57 | install | libv4l1-0 | 1.20.0-2.1
2020-09-15 13:16:58 | install | aaa_base-extras | 84.87+git20200909.ee4a72c-1.1
2020-09-15 13:16:58 | install | sudo-plugin-python | 1.9.2-3.1
2020-09-15 13:16:58 | install | libqt5-qtimageformats | 5.15.1-1.1
2020-09-15 13:16:58 | install | libqt5-qtbase-platformtheme-gtk3 | 5.15.1-1.1
2020-09-15 13:16:58 | install | libQt5X11Extras5 | 5.15.1-1.1
2020-09-15 13:16:59 | install | libQt5Widgets5 | 5.15.1-1.1
2020-09-15 13:16:59 | install | libqt5-qtstyleplugins-platformtheme-gtk2 | 5.0.0+git20170311-8.4
2020-09-15 13:16:59 | install | libQtQuick5 | 5.15.1-1.1
2020-09-15 13:16:59 | install | libQt5Svg5 | 5.15.1-1.1
2020-09-15 13:16:59 | install | libQt5PrintSupport5 | 5.15.1-1.1
2020-09-15 13:17:00 | install | libqt5-qtxmlpatterns-imports | 5.15.1-1.1
2020-09-15 13:17:00 | install | libQt5WebChannel5 | 5.15.1-1.1
2020-09-15 13:17:01 | install | libqt5-qtwebengine | 5.15.1-1.1
2020-09-15 13:17:01 | install | libQt5WebChannel5-imports | 5.15.1-1.1
2020-09-15 13:17:03 | install | discord | 0.0.12-15.1
Is there an easy way to determine which package update is causing the problem?

Thanks,
Gene
↧
Search

LEAP 15.2 HP LaserJet Pro MFP M28-M31- multifunction scanner error using xsane

September 16, 2020, 4:41 pm
$
0
0
I tried to do a couple of scans this evening, and got an error that my system needed a plugin to perform the scan.
All of my scan applications gave that error "plugin required".

xsane was active for all pf the following:
It gave me 2 choices.
1- search on the web(I assume HP? )
2- install from local.
Since I don't have that plugin 'local', I let it do the search.
Then a popup came up saying the plugin was ready, and 'root' password required.
I did that in xsane scanned. It was slow, (REALLY SLOW) but eventually the scan came through.

Did I mess up? Is there a system plugin that I could have installed from zypper or YaST?
Is there a way to make scans faster for this multi-function HP printer?

PS; I am just guessing the upgrade to Leap 15.2 took out the 'plugin' that was installed, since this is the first time I have scanned after the upgrade.
↧
↧

LEAP 15.2 Update Error Leap 15.2

September 16, 2020, 5:34 pm
$
0
0
Hi,
I am getting an update error
patch:openSUSE-2020-1421-1.noarch conflicts with
kio-core-debuginfo.x86_64
It happens every time it tries to update.
What should I do about this?
Thanks,
↧

LEAP 15.2 wireshark won't run on LEAP 15.2

September 17, 2020, 12:28 am
$
0
0
Installed wireshark from the 15.2 repo but it will not run as follows:


Code:
foo@bar:~> sudo wireshark
[sudo] password for root: 
qt.qpa.xcb: could not connect to display 
qt.qpa.plugin: Could not load the Qt platform plugin "xcb" in "" even though it was found.
error: XDG_RUNTIME_DIR not set in the environment.
Failed to create wl_display (No such file or directory)
qt.qpa.plugin: Could not load the Qt platform plugin "wayland" in "" even though it was found.
This application failed to start because no Qt platform plugin could be initialized. Reinstalling the application may fix this problem.
 
Available platform plugins are: eglfs, linuxfb, minimal, minimalegl, offscreen, vnc, wayland-egl, wayland, wayland-xcomposite-egl, wayland-xcomposite-glx, xcb.
 
Aborted
Is there a fix?

TIA!
↧

OTHER VERSION TW or Leap for Docker Server?

September 17, 2020, 1:48 am
$
0
0
I will be installing OpenSuse on this hw: HPE Proliant DL380 G7 with 144GB DDR3 RAM and 2x2.6GHz XEON CPU - upgradeable to 3.4GHz - and 16 SAS 2'5 drives. Got 2 identical servers that will be clustered if I can manage that.

Hardware requirements have been checked and everything seems to work out. Have tested a Live CD with Leap and it even detected and configured the network, based on 2 Broadcom NIC that other*nix distro have issues with. (Debian).

So, intended usage:

  • Webmin, www.webmin.com
  • Docker - via Podman ?
    • Nextcloud
    • Matomo
    • Firewall (probably OPNSense but I am also considering a separate box for this)
    • Traefik
    • Ubiquiti UNMS
    • Sphinx
    • MySQL + PHP (Nginx/MariaDB) web lab. Wordpress - Piwigo etc...
    • etc...


So when I say Docker some people say I should go Tumbleweed since it has better support for later versions of Podman - 2. Opinions about that? Leap "only" has Podman 1.

I am REALLY hoping for this to come together without to much hands on fixing in conf files and such. Then I will be asking here, probably a lot. Some Docker distros have terrible docs, other better, and many are to me rather incomprehensible. But first thing is first... Leap or TW?
↧
↧

LEAP 15.2 Software Where?

September 17, 2020, 2:25 am
$
0
0
Just installed Leap 15.2 KDE. It's a long time since I've used Suse/OpenSuse but I do remember that there was a lot more listed in Yast software than is now the case. The lists are tiny compared to what they used to be. It looks very bleak.
Is this how it's supposed to be?
I've installed the Packman repository, but that doesn't seem to have made much, if any, difference.
If this is all you now get then I'll have install another distro.
Which would be a shame because the rest of the distro is first rate.
↧

LEAP 15.2 Digikam - Photograph Inpainting tool

September 17, 2020, 2:48 am
$
0
0
Does anyone know if, the Digikam Photograph Inpainting tool is included in the openSUSE packages?
  • I've installed Digikam Version 7.1.0 on Leap 15.2 and, can't find it – it also seemed to be not included with version 6.4.0 …

Installed Digikam packages:
Code:
S  | Name            | Summary                          | Type
---+-----------------+----------------------------------+--------
i+ | digikam        | A KDE Photo Manager              | package
i+ | digikam-lang    | Translations for package digikam | package
i+ | digikam-plugins | DigiKam plugins                  | package
i  | libdigikamcore7 | The main digikam libraries      | package
↧

LEAP 15.1 Screen except mouse movements freezes

September 17, 2020, 4:35 am
$
0
0
Hello,

Problem: Screen except mouse movements freezes due to reasons I could not grasp.

Diagnostics:
  • I have attached the output of `journalctl -b`: https://gofile.io/d/Px1ezd
  • Details:
    • GNOME v 3.62.2
    • Graphics: GeForce GTX 460/PCle/SSE2
    • OS: openSUSE Leap 15.1
    • OS type: 64-bit

I would appreciate if someone points me in the right direction.

Please let me know if anything further needed to identify the problem, or needs further elaboration.

Many thanks.
↧
Search

LEAP 15.1 UTF-8 not rendered by kate for some files

September 17, 2020, 5:01 am
$
0
0
I have a script that creates several files, each beginning with Zero Width No- Break Space ('EF BB BFX, BOM) and containing Hebrew text in UTF-8. When I open them in kate, some render correctly and some don't. However, LibreOffice correctly renders a file that kate garbled.

As an example, in a file called katz.out, kate renders "H: הרב שְׁמוּאֵל יְהוּדָה בַּר צְבִי יַעֲקֹב הַכֹּהֵן" as "H: ה׹ב שְׁמו֌אֵל יְהו֌ד֞ה ב֌ַך שְב֮י יַעֲקֹב הַכֹ֌הֵן".

Any idea what's causing this?
↧
↧

LEAP 15.1 During boot system pauses about 10 secs

September 17, 2020, 5:45 am
$
0
0
I have two 15.1 systems here, only one of them shows the problem.

I can also boot the one with the problem in 13.1, which does not show the problem.

The problem is that during the boot the sytem pauses, not doing anything. Even the screen goes sleeping after a few seconds.
After about 10 secs the system returns to life and finishes booting and all is fine then.

I tried o find out what is displayed before and/or after this delay (all is going very fast) and I have the idea that it is somewhere around this snippet from dmesg:
Code:
[    4.211081] usbcore: registered new interface driver ums-realtek
[    4.350006] [drm] ring test on 0 succeeded in 1 usecs
[    4.350010] [drm] ring test on 1 succeeded in 1 usecs
[    4.350014] [drm] ring test on 2 succeeded in 1 usecs
[    4.350021] [drm] ring test on 3 succeeded in 3 usecs
[    4.350026] [drm] ring test on 4 succeeded in 3 usecs
[    5.526989] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[    6.546928] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[    7.566899] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[    8.586871] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[    9.606843] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[  10.626814] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[  11.646786] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[  12.666757] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[  13.686729] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[  14.706700] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, trying to reset the VCPU!!!
[  14.726700] [drm:uvd_v1_0_start [radeon]] *ERROR* UVD not responding, giving up!!!
[  14.726764] radeon 0000:01:00.0: failed initializing UVD (-1).
[  14.726910] clocksource: Switched to clocksource tsc
[  14.727088] [drm] ib test on ring 0 succeeded in 0 usecs
[  14.727184] [drm] ib test on ring 1 succeeded in 0 usecs
[  14.727208] [drm] ib test on ring 2 succeeded in 0 usecs
[  14.727233] [drm] ib test on ring 3 succeeded in 0 usecs
[  14.727265] [drm] ib test on ring 4 succeeded in 0 usecs
[  14.727537] [drm] Radeon Display Connectors
Journalctl shows the same messages about UVD and VCPU (no idea what it is), but even in read!

Any ideas on how to investigate further.
↧

Tumbleweed Snapshots bring updated Inkscape, Node.js, KDE Applications

September 17, 2020, 8:10 am
$
0
0
Four openSUSE Tumbleweed snapshots were released since the last article. KDE’s Applications 20.08.1, Node.js, iproute2 and inkscape were updated in the snapshots throughout the week. The 20200915 snapshot is trending stable at a rating of 97, according to the Tumbleweed snapshot reviewer. Many YaST packages were updated in this snapshot....

More...
↧

LEAP 15.2 Hard Disk Activity Memory Hole

September 17, 2020, 10:16 am
$
0
0
I do not know where else to post this, so here goes. I have a clean basic XFCE installation of OpenSUSE LEAP 15.2. This behavior happens on both the Asus R541U laptop I used to have (8GB RAM, 512MB Swap) and my new Dell Inspiron 7591 (16GB RAM, 1GB swap). I would boot into OpenSUSE to do some "hard drive wrangling", i.e. making disk images of hard drives via USB adapters (dd if=/some/device | gzip -c > imagefile) or zeroizing old disks (dd if=/dev/zero of=/some/device).

As soon as I begin the dd process, my RAM and swap climb through the roof. Almost no applications are open when this occurs. For example:

1) When I was using my Asus to read the 512GB SSD via an adapter to another USB external hard drive (BACKUP) (i.e. dd if=/dev/nvme0n1 | gzip -c > /run/media/robert/BACKUP/Windows/dell7591.img.gz)

2) When I was backing up my files on the Asus (rsync -Hav /home/robert/ /run/media/robert/BACKUP/dell/robert/)

3) When I was copying the dd image to the new 1TB SSD upgrade for my dell (gunzip -c /run/media/robert/BACKUP/Windows/dell7591.img.gz | dd of=/dev/nvme0n1)

4) When I was just now zeroizing the old 512GB SSD via the same USB adapter (dd if=/dev/zero of=/dev/sdb)

5) When I was synchronizing my incremental monthly backups (both 2TB external USB drives running LUKS) (rsync -Hav --delete --progress /run/media/robert/BACKUP/ /run/media/robert/BACKUP2/ )

It always seems connected to rsync/gzip/dd, i.e. heavy use of filesystems. If I boot OpenSUSE and I am just sitting in OpenSUSE using applications, usually it does not cause me to dig into swap.

At the height of the zeroizing action, for example, swap use (16GB RAM, 1GB swap, new Dell Inspiron 7591) climbed to 108MB. It dropped to 11MB.

Given that I have 16GB of RAM, such behavior is absolutely unacceptable. All the I/O should be happening on disks. I have not been able to triangulate, using top, what process is eating RAM so much.

I am using EXT4 exclusively, no BTRFS anywhere.

I have remounted all tmpfs entries to only give them 1GB of RAM to work with, as in the past this has prevented such excessive swappiness (believe it or not; it's difficult to prove; older versions of OpenSUSE, etc).

I am willing to run experiments to see what's going on.

I noticed that there were some btrfs components of systemd that were installed. I uninstalled them, but the problem remains.

I don't understand how even running something complex as rsync + gzip + dd should need to dig into that much system RAM. I mean, I have 16GB!

Have any memory leaks been reported on OpenSUSE?
↧

LEAP 15.2 Bootable USB Size

September 17, 2020, 10:30 am
$
0
0
Hi,

After years of live upgrades from one OpenSUSE version to the next, the new LEAP 15.2 version will be installed onto a new completely blank system replacing my 8 year old one.

For this purpose, I am trying to get started with the Bootable USB option. The Install Page claims the disk image requires 3.99GB but have not been able to write onto any of my USB drives which are all 4GB. The issue is that the OpenSUSE Studio Image Writer seems to think they are 3.84GB disks! This could be due to formatting overhead but I fully expect to overwrite the entire USB disk and so don't mind losing whatever is eating up those missing 0.16GB.


  1. Is there a way to write the Bootable USB image directly into the RAW USB disk so that it ignores any file-system overhead?
  2. Is there a way to wipe the USB clean so that it is correctly recognized as having 4GB?


Although not entirely related to the problem, would the Bootable USB image be usable on a device indirectly? Specifically, I have tons of SD and MicroSD cards that are over 4GB and I could use those if it is possible to boot from a USB card-reader, of which I also have plenty.

Thank you,

- Itai
↧
↧

LEAP 15.2 Policy Kit decides to use a partition

September 17, 2020, 12:36 pm
$
0
0
I have upgraded to 15.2 from previous version.

Right after the boot, while Plasma is starting, the policy kit (PolKit1) wants to mount a partition, and asks root's password for that.

I don't want that partition to be mounted. There is nothing said about the partition in fstab.

In System Settings -> Removable Storage -> Removable Devices -> Device Overrides, the partition is neither listed to be automounted at login nor to be automounted on attach (all boxes are unchecked in the table).

There are other partitions in the computer, which policy kit does not want to mount.

How can I disable that undesirable behavior of the policy kit? I haven't configured it in any way.
↧

LEAP 15.2 Unable to change virtual machine power state... after upgrading vmware workstation to 15.5.6

September 17, 2020, 2:18 pm
$
0
0
After upgrading all my suspended machines return the error
Unable to change virtual machine power state: Transport (VMDB) error -14: Pipe connection has been broken.

And some of the non suspended VMs (but not all of them) other error
VMware Workstation unrecoverable error: (svga)
Unexpected signal: 4.


When I did the upgrade I had to do this because the installation was not working.
I have tried to uninstall and install again but it dind't kork.

It's Workstation pro.
↧
Search

TUMBLEWEED Why openSUSE Tumbleweed installed on bare metal cannot boot from Hyper-V?

September 17, 2020, 10:52 pm
$
0
0
I installed openSUSE Tumbleweed and Ubuntu on the same SSD in my computer. I use Windows most of the time but sometimes I do need to use Linux and I don't want to reboot to that SSD. So I choose to run a VM from that SSD with both Linux. I'm also a frequent Windows Sandbox (based on Hyper-V) user, and back a few months ago, Windows hates hypervisor other than Hyper-V and I'm stuck with it. (Please don't ask me why I bother with Windows Sandbox in the first place, I love it.)

It will reach a certain target, get stuck for a while then a watchdog is triggered, something like initramfs timeout will spam all over the screen for a while, then drawn into initramfs emergency shell.

I tried to lookup the log inside the initramfs, nothing stand out, but the same initramfs timeout appeared in the end of the log, as I expected.

At the same time, that Ubuntu installation will boot under Hyper-V just fine.

I tried to have a fresh install of openSUSE in Hyper-V for reference, and took a look on what package is missing on the Linux SSD. It turns out I didn't have hyper-v package installed, so I installed it and gave it another try, SNAFU again. I expected this because it after installing that package, it didn't even initiate regernerating the initramfs, where the trigger of the culprit is.

After Windows 10 Version 2004, finally VMWare can co-exist with Hyper-V, I tried VMWare Player out, it worked flawlessly.

Ok, so I already get it working, I'm still curious why Hyper-V didn't work while VMWare worked flawlessly, and why Ubuntu worked but openSUSE didn't?
↧

LEAP 15.2 btrfs-clean using 100% CPU when I have no btrfs filesystems

September 18, 2020, 12:07 am
$
0
0
Today I boot my computer and It is really slow. I open a terminal (after a while) and run a top command, btrfs-clean and some others btrfs proccess are taking a lot of CPU time, but I have no btrfs filesystems at all. I had to kill a couple of this proccess by hand and the problem was gone, altough it left a lot of zombie process

Code:
andromeda:~ # ps aux |grep btrfs
root      107  0.2  0.0      0    0 ?        I    08:34  0:02 [kworker/u12:1-btrfs-endio-write]
root      113  0.3  0.0      0    0 ?        I    08:34  0:03 [kworker/u12:5-btrfs-endio]
root      484  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-worker]
root      486  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-worker-hi]
root      487  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-delalloc]
root      488  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-flush_del]
root      489  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-cache]
root      490  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-submit]
root      491  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-fixup]
root      492  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-endio]
root      493  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-endio-met]
root      494  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-endio-met]
root      495  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-endio-rai]
root      496  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-endio-rep]
root      497  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-rmw]
root      498  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-endio-wri]
root      499  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-freespace]
root      500  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-delayed-m]
root      501  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-readahead]
root      502  0.0  0.0      0    0 ?        I<  08:34  0:00 [btrfs-qgroup-re]
root      505 13.9  0.0      0    0 ?        S    08:34  2:21 [btrfs-cleaner]
root      506 10.0  0.0      0    0 ?        S    08:34  1:42 [btrfs-transacti]
root      741  0.2  0.0      0    0 ?        I    08:35  0:03 [kworker/u12:7-btrfs-endio-write]
root      769  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-worker]
root      770  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-worker-hi]
root      771  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-delalloc]
root      772  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-flush_del]
root      773  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-cache]
root      774  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-submit]
root      775  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-fixup]
root      776  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-endio]
root      777  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-endio-met]
root      778  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-endio-met]
root      779  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-endio-rai]
root      780  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-endio-rep]
root      781  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-rmw]
root      782  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-endio-wri]
root      783  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-freespace]
root      784  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-delayed-m]
root      785  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-readahead]
root      786  0.0  0.0      0    0 ?        I<  08:35  0:00 [btrfs-qgroup-re]
root      1042  0.0  0.0      0    0 ?        S    08:35  0:00 [btrfs-cleaner]
root      1043  0.1  0.0      0    0 ?        S    08:35  0:01 [btrfs-transacti]
root      9984  0.2  0.0      0    0 ?        I    08:46  0:00 [kworker/u12:0-btrfs-endio-write]
root    10085  0.0  0.0      0    0 ?        I    08:48  0:00 [kworker/u12:2-btrfs-endio-write]
root    10086  0.0  0.0      0    0 ?        I    08:48  0:00 [kworker/u12:3-btrfs-worker]
root    10087  0.0  0.0      0    0 ?        I    08:48  0:00 [kworker/u12:4-btrfs-endio-write]
root    10088  0.0  0.0      0    0 ?        I    08:48  0:00 [kworker/u12:6-btrfs-freespace-write]
root    10204  0.0  0.0      0    0 ?        I    08:49  0:00 [kworker/u12:8-btrfs-endio-write]
root    10328  0.0  0.0  7432  824 pts/2    R+  08:51  0:00 grep --color=auto btrfs
andromeda:~ #

why?


best regards
↧
↧

[security-announce] openSUSE-SU-2020:1415-1: moderate: Security update for python-Flask-Cors

September 18, 2020, 10:00 am
$
0
0
openSUSE Security Update: Security update for python-Flask-Cors ______________________________________________________________________________ Announcement ID: openSUSE-SU-2020:1415-1 Rating: moderate References: #1175986 Cross-References: CVE-2020-25032 ...

More...
↧

[security-announce] openSUSE-SU-2020:1416-1: moderate: Security update for openldap2

September 18, 2020, 10:00 am
$
0
0
openSUSE Security Update: Security update for openldap2 ______________________________________________________________________________ Announcement ID: openSUSE-SU-2020:1416-1 Rating: moderate References: #1174154 Cross-References: CVE-2020-15719 Affected...

More...
↧

[security-announce] openSUSE-SU-2020:1420-1: Security update for gimp

September 18, 2020, 10:00 am
$
0
0
openSUSE Security Update: Security update for gimp ______________________________________________________________________________ Announcement ID: openSUSE-SU-2020:1420-1 Rating: low References: #1073627 Cross-References: CVE-2017-17789 Affected Products:...

More...
↧
Viewing all 40713 articles
Browse latest View live
Search
<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>